Symbol Technologies Crib PL360 User Manual

PL360/460 Cradle  
Quick Reference Guide  
 
Quick Reference Guide  
3
Introduction  
The PhaserLink 360/460 cradle acts as a stand, host communication interface,  
and charger for the Phaser scanner. For convenience, the cradle can sit on a  
desktop or be mounted on a wall.  
The cradle receives data from the scanner via connectors in the bottom of the  
scanner and the top of the cradle. It then transmits that data to the host device  
through an attached cable.  
The cradle also provides power for charging the scanner battery pack (in the  
scanner). The cradle has a charge status indicator light.  
Two versions of the cradle are available:  
-
-
PL 460 cradle: the batch retail version.  
PL 360 cradle: the batch industrial version.  
This Quick Reference Guide provides basic instruction on the set up and use of  
the cradle. Unless otherwise noted, the term PhaserLink refers to all versions of  
the cradle.  
Equipment Supplied  
The following equipment is supplied:  
-
-
-
-
-
Two screws (for wall mounting).  
One Velcro strip (for desk mounting).  
Four rubber feet (for desk mounting).  
This Quick Reference Guide.  
PhaserLink cradle.  
Save the shipping container for storing or shipping. Inspect all equipment for  
damage. If anything is damaged or missing, call your authorized Customer  
Support Representative immediately.  
Related Documentation  
-
-
Phaser Series Scanner Product Reference Guide, p/n 70-33629-xx.  
P360/460 Memory Scanners Quick Reference Guide, p/n 70-33628-xx.  
 
4
PL360/460 Cradle  
Parts  
Scanner Support Tab  
Charging/Communication Contacts  
Charging  
LED  
Indicator  
COM 1  
Power  
Port  
COM 2  
Wall-mounting  
Socket 1  
Wall-mounting  
Socket 2  
 
Quick Reference Guide  
5
Connecting to the Host  
There are three ports on the bottom of the cradle.  
COM 1  
COM 2  
Power Port  
COM 1 connects to the host computer; COM 2 is used for daisy-chaining multiple  
cradles together; and, the Power Port supplies power to the cradle.  
1. Insert the independent power plug into the  
Power Port. (The cradle cannot be powered  
by the host computer.)  
2. Insert the cable from the host computer into  
COM 1.  
3. Insert the cable to the other cradles, if any,  
into COM 2.  
Daisy-Chaining  
NOTE The cradle supports daisy-chaining when connected to a serial  
host and not when using Synapse interfaces.  
To daisy-chain two or more cradles together, connect COM 1 of the first cradle to  
the host and COM 2 to COM 1 of the second cradle. Then connect COM 2 of the  
second cradle to COM 1 of the third cradle. Up to 12 cradles can be daisy-chained  
to one host.  
 
 
6
PL360/460 Cradle  
Wall Mounting  
Before wall-mounting the cradle, the scanner support tab must be changed from  
the desk-mount position to the wall-mount position.  
1
1. Lift the scanner support tab out of  
the top part of the cradle and  
replace it in the wall-mount  
position as shown.  
2. Seat the cables from the bottom of  
the cradle in the grooves along the  
length of the cradle so that the  
bottom of the cradle is smooth and  
flat.  
3. Secure two screws (included) to  
the wall. A template is provided on  
Desk Mount  
Wall Mount  
-
Fasten the screws into the wall  
where the cradle should hang  
leaving about 1/8” (.3 cm) of  
the screw outside the wall for  
the cradle wall moung sockets.  
2
4. Place the cradle over the screw  
heads and slide down until it fits  
into place. Slight pressure  
upwards should not move the  
cradle.  
5. Place the Phaser scanner in the  
cradle.  
3
 
Quick Reference Guide  
7
Inserting Phaser in the Cradle  
Place the Phaser scanner in the cradle so that the top of the scanner sits in the  
larger part of the cradle and the metal contacts on the bottom of the scanner touch  
the contacts on the cradle.  
Sending Data to the Host Computer  
To set up the PhaserLink cradle for communication between a Phaser scanner  
and a host computer:  
1. Connect the cradle to the host computer as described in  
2. Insert the Phaser scanner in the cradle.  
3. Start the communication program on the host computer and the Phaser  
scanner.  
Recharging the Battery in the Phaser  
4. Connect the cradle to a receptacle supplying AC power of the proper voltage  
level.  
5. Place the scanner in the cradle, ensuring the metal contacts on the bottom of  
the scanner touch the contacts on the cradle.  
6. A complete charge takes up to 4 hours, depending upon the remaining charge  
in the scanner battery.  
Indicator LED  
When the scanner is placed in the cradle, it waits 15 minutes to start charging the  
battery in the scanner. The LED indicates the charging status as follows:  
LED  
Description  
The scanner is not in the cradle.  
Scanner is in cradle but not charging.  
Scanner is in cradle and charging.  
Off  
Slow Blink  
Fast Blink  
On  
Scanner is in cradle and the charge cycle is  
complete.  
 
8
PL360/460 Cradle  
Troubleshooting  
If the cradle does not work after following the operating instructions in this guide:  
check the system power.  
check for loose cable connections.  
ensure the scanner is sitting properly in the cradle.  
Cleaning  
Wipe the cradle periodically with a lens tissue or other material suitable for  
cleaning optical material, such as eyeglasses.  
CAUTION Do not pour, spray or spill any liquid on the cradle.  
Regulatory Information  
All Symbol devices are designed to be compliant with rules and regulations in locations they  
are sold and are labeled as required.  
Any changes or modifications to Symbol Technologies equipment, not expressly approved by  
Symbol Technologies, could void the user's authority to operate the equipment.  
CAUTION Only use Symbol approved and UL Listed accessories, battery packs and  
battery chargers.  
Do NOT attempt to charge damp/wet mobile computers or batteries. All components must be  
dry before connecting to an external power source.  
Country Approvals  
Regulatory markings are applied to the device signifying the device is approved for use in the  
following countries: United States, Canada, Australia, Japan and Europe.  
Please refer to the Symbol Declaration of Conformity (DoC) for details of other country  
markings. This is available at http://www2.symbol.com/doc/.  
Operation of the device without regulatory approval is illegal.  
Health and Safety Recommendations  
Ergonomic Recommendations  
CAUTION In order to avoid or minimize the potential risk of ergonomic injury follow the  
recommendations below. Consult with your local Health & Safety Manager  
to ensure that you are adhering to your company's safety programs to  
prevent employee injury.  
-
-
-
-
-
Reduce or eliminate repetitive motion.  
Maintain a natural position.  
Reduce or eliminate excessive force.  
Keep objects that are used frequently within easy reach.  
Perform tasks at correct heights.  
 
Quick Reference Guide  
9
-
-
-
-
-
-
Reduce or eliminate vibration.  
Reduce or eliminate direct pressure.  
Provide adjustable workstations.  
Provide adequate clearance.  
Provide a suitable working environment.  
Improve work procedures.  
Vehicle or Forklift Installation  
Position your device within easy reach. Be able to access your device without removing your  
eyes from the road.  
Laser Devices  
Complies with 21CFR1040.10 and 1040.11 except for deviations pursuant to Laser Notice No.  
50, dated July 26, 2001.  
EN60825-1:1994+ A1:2002 +A2:2001  
IEC60825-1:1993+A1:1997+A2:2001  
The laser classification is marked on one of the labels on the device.  
Class 1 Laser devices are not considered to be hazardous when used for their intended  
purpose. The following statement is required to comply with US and international regulations:  
CAUTION Use of controls, adjustments or performance of procedures other than  
those specified herein may result in hazardous laser light exposure.  
Class 2 laser scanners use a low power, visible light diode. As with any very bright light  
source, such as the sun, the user should avoid staring directly into the light beam. Momentary  
exposure to a Class 2 laser is not known to be harmful.  
Cradle Labeling  
 
10  
PL360/460 Cradle  
In accordance with Clause 5, IEC 825 and EN60825, the following information is provided to  
the user:  
ENGLISH  
CLASS 1  
CLASS 2  
HEBREW  
CLASS 1 LASER PRODUCT  
LASER LIGHT  
DO NOT STARE INTO BEAM  
CLASS 2 LASER PRODUCT  
DANISH / DANSK  
ITALIAN / ITALIANO  
KLASSE 1  
KLASSE 2  
KLASSE 1 LASERPRODUKT  
LASERLYF  
CLASSE 1  
CLASSE 2  
PRODOTTO AL LASER DI CLASSE 1  
LUCE LASER  
SE IKKE IND I STRÅLEN  
KLASSE 2 LASERPRODUKT  
NON FISSARE IL RAGGIOPRODOTTO  
AL LASER DI CLASSE 2  
DUTCH / NEDERLANDS  
NORWEGIAN / NORSK  
KLASSE 1  
KLASSE 2  
KLASSE-1 LASERPRODUKT  
LASERLICHT  
NIET IN STRAAL STAREN  
KLASSE-2 LASERPRODUKT  
KLASSE 1  
KLASSE 2  
LASERPRODUKT, KLASSE 1  
LASERLYS IKKE STIRR INN I LYSSTRÅLEN  
LASERPRODUKT, KLASSE 2  
FINNISH / SUOMI  
PORTUGUESE / PORTUGUÊS  
LUOKKA 1  
LUOKKA 2  
LUOKKA 1 LASERTUOTE  
LASERVALO  
ÄLÄ TUIJOTA SÄDETTÄ  
LUOKKA 2 LASERTUOTE  
CLASSE 1  
CLASSE 2  
PRODUTO LASER DA CLASSE 1  
LUZ DE LASER NÃO FIXAR O RAIO LUMINOSO  
PRODUTO LASER DA CLASSE 2  
FRENCH / FRANÇAIS  
SPANISH / ESPAÑOL  
CLASSE 1  
CLASSE 2  
PRODUIT LASER DE CLASSE 1  
LUMIERE LASER  
CLASE 1  
CLASE 2  
PRODUCTO LASER DE LA CLASE 1  
LUZ LASER  
NE PAS REGARDER LE RAYON FIXEMENT  
PRODUIT LASER DE CLASSE 2  
NO MIRE FIJAMENTE EL HAZ  
PRODUCTO LASER DE LA CLASE 2  
GERMAN / DEUTCH  
SWEDISH / SVENSKA  
KLASSE 1  
KLASSE 2  
LASERPRODUKT DER KLASSE 1  
LASERSTRAHLEN  
NICHT DIREKT IN DEN LASERSTRAHL SCHAUEN  
LASERPRODUKT DER KLASSE 2  
KLASS 1  
KLASS 2  
LASERPRODUKT KLASS 1  
LASERLJUS STIRRA INTE MOT STRÅLEN  
LASERPRODUKT KLASS 2  
CHINESE / ㅔԧЁ᭛  
KOREAN /G䚐ạ㛨  
1ꢀ㉏ꢀ  
1ꢀ㉏▔
ܝ
ѻકꢀ  
ܝ
 
X☥ἽG  
Y☥ἽG  
GG  
X☥ἽG⤼㢨㤴G㥐䖼  
2ꢀ㉏ꢀ  
⤼㢨㤴Gṅ㉔  
㢨Gṅ㉔㡸G㨰㐐䚌㫴G⫼㐡㐐㝘U  
Y☥ἽG⤼㢨㤴G㥐䖼  
ߛ
⊼㾚
ܝ
ᴳ  
2ꢀ㉏▔
ܝ
ѻક  
GG  
JAPANESE / ᣣᧄ⺆ꢀꢀꢀ  
ࠬꢁ
ޓ
ࠬꢁꢀ
࡯࡟
ࠩ⵾ຠ  
ࠬꢂ
࡯࡟ޓ
ࠩశ✢  
శ✢
⋥ⷞ
޿ߐߛߊߢ޿ߥߒ
 
ࠬꢂꢀ
࡯࡟
ࠩ⵾ຠ  
Power Supply  
Use only a Symbol approved power supply 50-14000-101R output rated 9 Vdc and minimum  
1 A. The power supply is certified to EN60950-1 with SELV outputs. Use of an alternative  
power supply invalidates any approval given to this device and may be dangerous.  
Batteries  
Please follow the local regulations when disposing of re-chargeable batteries.  
Taiwan - Recycling  
EPA (Environmental Protection Administration) requires dry battery producing or  
importing firms in accordance with Article 15 of the Waste Disposal Act are required to  
 
Quick Reference Guide  
11  
indicate the recycling marks on the batteries used in sales, giveaway or promotion.  
Contact a qualified Taiwanese recycler for proper battery disposal.  
Symbol Rechargeable Batteries  
Symbol rechargeable battery packs are designed and constructed to the highest standards  
within the industry. However, there are limitations to how long a battery can operate or be  
stored before needing replacement. Many factors affect the life of a battery pack such as heat,  
cold, customer usage profiles, age, and severe drops.  
When batteries are stored over a year, battery cell manufacturers advise that some  
irreversible deterioration in overall battery quality may occur. To minimize this loss, they  
recommend storing batteries half charged in a dry, cool place between 41° and 77°F (5° and  
25°C), the cooler the better) and removed from the equipment to prevent the loss of capacity.  
Batteries should be charged to half capacity at least once a year. If an electrolyte leakage is  
observed, avoid any contact with the affected area and properly dispose of the battery.  
Replace the battery when a significant loss of run time is detected. Batteries must be charged  
within the 32° to 104°F (0° to 40°C) temperature range.  
The standard warranty period for all Symbol batteries is 30 days, regardless if the battery was  
purchased separately or included as part of the mobile computer. For more information on  
Radio Frequency Interference Requirements-FCC  
Note: This equipment was tested and found to comply with the limits for a  
Tested to comply  
with FCC Standards  
Class B digital device, pursuant to Part 15 of the FCC rules. These limits  
are designed to provide reasonable protection against harmful interference  
in a residential installation. This equipment generates, uses and can  
FOR HOME OR OFFICE USE  
radiate radio frequency energy and, if not installed and used in accordance with the  
instructions, may cause harmful interference to radio communications. However there is no  
guarantee that interference will not occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged to try to correct the interference by  
one or more of the following measures:  
-
-
-
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the  
receiver is connected.  
-
Consult the dealer or an experienced radio/TV technician for help.  
Radio Frequency Interference Requirements - Canada  
This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.  
 
12  
PL360/460 Cradle  
Marking and European Economic Area (EEA)  
Statement of Compliance  
Symbol Technologies, Inc., hereby, declares that this device is in compliance with the  
essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of  
Conformity may be obtained from http://www2.symbol.com/doc/.  
Waste Electrical and Electronic Equipment (WEEE)  
English: For EU Customers: All products at the end of their life must be returned to Symbol  
for recycling. For information on how to return product, please go to:  
Dansk: Til kunder i EU: Alle produkter skal returneres til Symbol til recirkulering, når de er  
udtjent. Læs oplysningerne om returnering af produkter på:  
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer  
zum Recycling an Symbol zurückgesandt werden. Informationen zur Rücksendung von  
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise  
eesmärgil Symbol'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun  
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a  
Symbol al final de su ciclo de vida para que sean reciclados. Si desea más información sobre  
Français : Clients de l'Union Européenne : Tous les produits en fin de cycle de vie doivent  
être retournés à Symbol pour recyclage. Pour de plus amples informations sur le retour de  
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita  
devono essere restituiti a Symbol al fine di consentirne il riciclaggio. Per informazioni sulle  
modalità di restituzione, visitare il seguente sito Web:  
 
Quick Reference Guide  
13  
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Symbol vállalathoz kell  
eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos  
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur  
naar Symbol te worden teruggezonden voor recycling. Raadpleeg  
terugzenden van producten.  
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à  
Symbol para reciclagem. Para obter informações sobre como devolver o produto, visite:  
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju  
Symbol za reciklažo. Za informacije o vraèilu izdelka obišèite:  
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi  
Symbol-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on  
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till  
Symbol för återvinning. Information om hur du returnerar produkten finns på  
 
14  
PL360/460 Cradle  
Wall Mounting Template  
1 5/16”  
Wall  
Mounting  
Socket 1  
Use 1/8” drill bit  
for the screw  
holes.  
Center  
Line of  
Cradle  
3 1/2”  
Wall  
Mounting  
Socket 2  
11/16”  
 
 
Quick Reference Guide  
15  
This page is intentionally blank.  
 
Service Information  
Before you use the unit, it must be configured to operate in your facility’s network  
and run your applications.  
If you have a problem running your unit or using your equipment, contact your  
facility’s Technical or Systems Support. If there is a problem with the equipment,  
they will contact the Symbol Support Center:  
United States  
United Kingdom  
Australia  
1-800-653-5350  
0800 328 2424  
1-800-672-906  
Canada  
Asia/Pacific  
Austria/Österreich 01-5055794-0  
905-629-7226  
337-6588  
Denmark/Danmark 7020-1718  
Finland/Suomi  
Germany/  
9 5407 580  
6074-49020  
France  
01-40-96-52-21  
Deutschland  
Mexico/México  
Norway/Norge  
Italy/Italia  
Netherlands/Nederla 315-271700  
2-484441  
5-520-1835  
+47 2232 4375  
nd  
South Africa  
Sweden/Sverige  
11-809 5311  
08 445 29 00  
Spain/España  
Europe/Mid-East  
Distributor  
+913244000  
Contact local  
distributor or call  
+44 118 945 7360  
Operations  
Latin America  
Sales Support  
Inside USA: 1-800-347-0178;  
Outside USA: +1.954.255.2610  
For the latest version of this guide go to: http://www.symbol.com/manuals.  
70-33657-01  
Revision D - May 2006  
Symbol Technologies, Inc.  
One Symbol Plaza Holtsville, N.Y. 11742-1300  
 

Sharp Cash Register XEA 201 User Manual
Sony Bluetooth Headset MDR AS700BT User Manual
Sony Flat Panel Television 4 116 578 111 User Manual
Sony Photo Printer Professional Photo Printer User Manual
Sony Speaker System SRS BTM30 User Manual
Sony Stereo System CMT CP33MD User Manual
Sunbeam Convection Oven CO3000 User Manual
Suncast Pet Care Product dh350 User Manual
Sun Microsystems Computer Drive CP32x0 User Manual
Tamron Camera Lens AFB005C700 User Manual